BGM ignition base plates and ignition kits are the solid basis for a high-quality engine. The powerful alternator guarantees perfect light output, the HQ ignition components a clean and powerful engine. Ideal for upgrading a decrepit, contact-controlled electrical system to a modern, maintenance-free high-performance ignition. ADVANTAGES: High light output due to maximum number of windings Proven excitation coil with copper plate for maximum reliability Pickup with [...]

bgm - Item number: BGM6010S20 Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,04 kg Category: Engine> Gearbox> Shims Other customers who are looking for gear shims -BGM ORIGINAL- Lambretta Series 1-3 - 2,00mm are interested, also looked for: Gear shim | Thrust washer | Washer gear | Gear disc | Spacer [...]

When choosing crankshaft bearings, you should always pay attention to high quality. We have put together BGM ORIGINAL bearing sets for you here. In addition to quality bearings, the kit also includes high-quality shaft seals. Each part of the bearing set is at least at the original manufacturer level. Shaft seals in this set are only supplied by Corteco. bgm - Article number: BGM1110 [...]

bgm - Item number: BGM6478TX Availability: in stock (Please check availability here in the Scooter Center Shop) Weight: approx. 0,15 kg Category: Workshop supplies> Trains Other customers who are interested in end cap for outer cable -BGM ORIGINAL- Ø inside = 8mm - 10pcs. interested, also searched for: end cap | Outer cable | End cap | Pull sleeve | Pull cap | Sleeve | Grommet [...]

Clutch linings are a very important link between the engine and the transmission. A well-functioning clutch is essential for driving fun, safety and performance. Unfortunately, many manufacturers do not make the appropriate effort with such an important component with the result that the clutches go through or do not separate properly. The covering manufacturers deliver the proper quality [...]

bgm - Item number: 7676603 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,04 kg Category: Motor> Rubber parts> Bushings Other customers who are interested in bushing silent rubber shock absorber / motor -BGM ORIGINAL ( Made in Germany) Ø = 9mm x 44mm- Vespa VNA, VNB, VBA, VBB are interested, also looked for: Bush | Silent rubber [...]

bgm - Item number: BGM0292HS15 Availability: in stock (Please check the availability here in the Scooter Center Shop) Weight: approx. 0,05 kg Category: Engine> Seals> Spacer Other customers who are interested in Spacer cylinder head -BGM ORIGINAL Ø52.5mm- Vespa PX125, Cosa125, GT125, GTR125, TS125, Super125 - 1.5mm are interested, also looked for: Spacer | Cylinder head | Distance seal [...]

Special tools - Made in Germany Assemble a bearing quickly and easily like a professional. That is possible with this quality tool. The bearing is neatly guided and cannot tilt. The motor housing is protected. Used to mount the roller bearing of the auxiliary shaft in the small engine half (Lima side). Material: 42CroMo4 (1100Nmm² tensile strength!) Surface: blue galvanized TIP: [...]

bgm PRO wiring harness for all Lambrettas with electronic ignition. The wiring harness is made with as few cables as possible, so it corresponds to the ideal of minimal electronics. The wiring goes to CDI, voltage regulator, headlight connector in the steering head, brake light switch and taillight. There are no annoying clipboards. A piece of bougier tube for the cable branch of the ignition base plate is included in the scope of delivery. The wiring harness [...]

With the CDI holder from bgm it is possible to install a CDI for the electronic ignition on a Ciao of the first and second series without further modifications. The holder is simply placed under the two motor screws and attached to the motor. The following materials are required for assembly: 1. 4x washers M5x15x1,2mm 2. 2x self-locking nuts [...]

Plastic storage dummy. This allows the crankshaft to be mounted and moved in the engine housing on a trial basis and without any effort. Thus, for pure measurement purposes, neither the crankshaft nor new bearings are stressed. Ideal to control the control angle of the crankshaft (rotary valve inlet) or the cylinder (exhaust angle, overcurrent angle). Made in Germany (US) bgm - Item number: BGM1204TL Availability: in stock (Please check the [...]

The bgm PRO clutch steel disks are manufactured exactly flat and allow the clutch to be separated precisely. Due to the very good concentricity, the clutch can be perfectly dosed. The steel discs are available in the original thickness of 1,5 millimeters and in a sports version with a height of just 1,0 millimeters. The sport version enables the assembly of a lamellar disc, which [...]